This item is no longer available. Updated or related products shown below:

H6350 High-Voltage Brushless Ultra Torque High Speed Heli Cyclic Servo

H6350 High-Voltage Brushless Ultra Torque High Speed Heli Cyclic Servo

View Product Details


Image for H6205 HV Digital High Speed Heli Cyclic MG Servo from HorizonHobby
+ / - Hover over image to Zoom
H6205 HV Digital High Speed Heli Cyclic MG Servo
  • Overview
  • Specs
  • Reviews
  • Parts & Accessories
  • Manuals & Support

Key Features

  • HV compatible
  • Blistering heli cyclic performance for 550-700 size helis with speeds of .07 and .05 sec/60° @ 6V and HV respectively.
  • High Precision with low deadband, high resolution, tight centering, and impressive holding torque.
  • Metal gear train for robust and rugged performance
  • Aluminum center section case doubles as a heat sink to keep the motor cool
Application: 550- to 700-size Heli
Bearing: Dual
Bushing Or Bearing: Bearing
Connector Type: Z-Connector
Connector Wire Gauge: 22 AWG
Connector Wire Length: 11.5 in (292mm)
Gear Material: Steel
Gear Type: Metal
Height: 1.25 in (31.8mm)
Input Voltage: 4.8–8.4V (High Voltage)
Length: 1.61 in (40.9mm)
Motor Type: Coreless
Programmable: No
Servo Type: Digital
Speed: 0.07 sec/60 deg @ 6.0V; 0.05 sec/60 deg @ 8.4V
Spline Count: 23 Teeth
Torque: 166 oz-in (12.0kg-cm) @ 6.0V; 238 (17.1kg-cm) @ 8.4V
Type: H6205 HV Digital Heli Cyclic Metal Gear Servo
Weight: 2.2 oz (61.7g)
Width: 0.82 in (20.9mm)

Parts Listing

$24.99  $22.49
In Stock
$24.99  $22.49
This item is no longer available

Optional Accessories

$49.99  $39.99
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
$24.99  $22.49
In Stock
In Stock



What's the difference between digital and analog servos?

Digital and analog servos have very similar construction and components. They both use the same type of motors, gears, cases, and have a potentiometer. A digital servo is different in the way it processes the incoming signal and converts that signal into servo movement. 

An analog servo when it receives a command to move, takes that signal and sends pulses to the servo motor at about 50 cycles per second, which in turn moves the motor to its required position determined by the potentiometer.

A digital servo has a micro-processor that receives the signal and then adjusts the pulse length and amount of power to the servo motor to achieve optimum servo performance and precision. A digital servo sends these pulses to the motor at a much higher frequency which is around 300 cycles per second. This helps eliminate deadband, provides a faster response to the servo motor, smoother motor movement, and has higher resolution and holding power than an analog servo.

There are some disadvantages to digital servos, but the disadvantages are not in any way close to out weighing the advantages. A digital servo will have a higher power consumption (Around 10 to 15 mAh per servo at idle) than an analog servo due to its higher pulse frequency, so larger capacity battery packs are recommended. Digital servos also are more expensive than analog servos which can get very costly in applications that require many servos.

What grease should I use on my servo gear train?

For JR servos we recommend Tamiya ceramic grease (TAM87025).

Why doesn't my servo center properly?

There are several scenarios which may attribute to this problem. 

1. The servo arm fit on the output spline may be loose.

2. There may be slop or wear in the gear train.

3. There may be slop or binding in the linkages.

4. You may have a faulty servo saver.

5 The push rods may be too flexible.

6. Improperly mounted servo (screws too tight, mounting rail too tight against the servo)

7. Faulty extention, damaged lead or dirty connector.

8. Worn or dirty pot.

Can I use a JR servo with a Futaba receiver?


Why can't you use the JR 8700G servo with FM?

The frequency on operation is so high that it feeds back with FM receivers.

Product Support Tips

Product Support

Technical questions about this Spektrum product should be directed to Horizon Hobby's Product Support Department:

Horizon Hobby, LLC.
ATTN: Product Support

2904 Research Road
Champaign, IL 61822

To place a Horizon Hobby Support Inquiry please visit our Inquiry Form Support Phone:(877) 504-0233
Fax:(217) 355-1552

Sales Support

If you would like to purchase this product, please go to the Store Locator or contact the Horizon Hobby Consumer Sales Department:

Horizon Hobby, LLC.
ATTN: Consumer Sales

2904 Research Road
Champaign, IL 61822
Email: Sales Phone:(800) 338-4639
Fax:(217) 355-1552